Unable to mount Root fs

      Unable to mount Root fs

      Hallo zusammen,



      mein Kathrein blebt beim Booten stehen. Im Hyperterminal erscheint folgende Ausgabe zuletzt bevor nichtsmehr geht:. Nehme an die letzte zeile ist das entscheidende. Update kann ich keines mehr durchführen. Kann auch nichtmehr nachvolziehen, was da schon alles gemacht wurde. Ist ursprünglich nicht mein receiver. Wollte die Kiste komplett zurücksetzen. Bitte um Hilfe!!



      Board: STb7100-mboard


      U-Boot 1.1.2 (STLINUX_2_0p1) (May 30 2007 - 16:03:49)

      DRAM: 32 MB
      write time out = 1, clock = 40
      write time out = 1, clock = 40
      Flash: 16 MB
      In: serial
      Out: serial
      Err: serial
      pll0 freq 531
      pll1 freq 400
      Net: VFD_Driver Init
      VFD_Controller Type : NEW Kathrein VFD
      board_version = 0
      Button_value = 7
      Hit any key to stop autoboot: 1 0
      ## Booting image at a0040000 ...
      Image Name: Linux 2.6
      Image Type: SH-4 Linux Kernel Image (gzip compressed)
      Data Size: 1806175 Bytes = 1.7 MB
      Load Address: 84401000
      Entry Point: 84402000
      Verifying Checksum ... OK
      Uncompressing Kernel Image ... OK

      Starting kernel console=ttyAS0,115200 root=/dev/mtdblock3 mem=32m bigphysarea=1024 coprocessor_mem=2m@0x04000000,2m@0x04200000 - 0x00000000 - 0 ...

      Linux version 2.6.11.12_stm20-33 (root@localhost) (gcc version 3.4.3 (STMicroelectronics/Linux Base 3.4.3-17) [build Sep 30 2005]) #8 Fri Jul 6 15:48:58 CEST 2007
      STMicroelectronics STb7100 Marusys MSS-5000 Custom board initialisation
      STb7100 version 3.x
      Built 1 zonelists
      Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock3 mem=32m bigphysarea=1024 coprocessor_mem=2m@0x04000000,2m@0x04200000
      st-coprocessor: Failed to reserve memory at 0x04000000
      st-coprocessor: Failed to reserve memory at 0x04200000
      PID hash table entries: 256 (order: 8, 4096 bytes)
      PLL1 : 531.00MHz
      PLL2 : 400.00MHz
      ST40 CPU : 265.50MHz
      ST40 BUS : 132.75MHz
      ST40 PER : 66.37MHz
      SLIM : 265.50MHz
      ST231 : 400.00MHz
      STBUS : 200.00MHz
      EMI : 100.00MHz
      LMI : 200.00MHz
      FSYN0_CHAN1 : 108.008MHz
      FSYN0_CHAN2 : 36.866MHz
      FSYN0_CHAN3 : 32.768MHz
      FSYN1_CHAN1 : 27.002MHz
      FSYN1_CHAN2 : 150.008MHz
      FSYN1_CHAN3 : 27.002MHz
      FSYN1_CHAN4 : 48.000MHz
      CLK_PIX_HD : 108.008MHz
      CLK_PIX_SD : 27.002MHz
      CLK_DISP_HD : 13.501MHz
      CLK_DISP_ID : 13.501MHz
      CLK_GDP2 : 27.002MHz
      CLK_656 : 27.002MHz
      CLK_PIPE : 150.008MHz
      CLK_PP : 27.002MHz
      CLK_IC_150 : 150.008MHz
      CLK_DAA : 32.768MHz
      CLK_DSS : 36.866MHz
      CLK_LPC : 46.875KHz
      CLK_BCH_HDMI : 108.008MHz
      CLK_TMDS_HDMI: 27.002MHz
      CLK_PIX_HDMI : 13.501MHz
      CLK_DVP : VIDINCLK
      CLK_RTC : 27.002MHz
      Console: colour dummy device 80x25
      Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
      Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
      Memory: 24608k/32768k available (3126k kernel code, 8116k reserved, 307k data, 104k init)
      Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
      CPU: STb710x
      NET: Registered protocol family 16
      SCSI subsystem initialized
      usbcore: registered new driver usbfs
      usbcore: registered new driver hub
      SH Virtual Bus initialized
      bigphysarea: Allocated 1024 pages at 0x847df000.
      Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
      JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
      Initializing Cryptographic API
      Device probe found data for platform device lirc
      lirc_dev: IR Remote Control driver registered, at major 61
      lirc_dev: lirc_register_plugin: sample_rate: 0
      STM LIRC plugin has IRQ 125
      Lirc STM: Using IRB mode
      STMicroelectronics LIRC driver configured
      STPIO layer initialised
      Device probe found data for platform device wdt
      STM watchdog initialized
      STMicroelectronics ASC driver initialized
      asc_init: check the clock
      ttyAS0 at MMIO 0xb8032000 (irq = 121) is a asc
      asc_init: check the clock
      ttyAS1 at MMIO 0xb8033000 (irq = 120) is a asc
      io scheduler noop registered
      io scheduler anticipatory registered
      io scheduler deadline registered
      io scheduler cfq registered
      RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
      tun: Universal TUN/TAP device driver, 1.6
      tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
      nwhw_config: device not found
      Generic ST boards onboard flash device: 0x01000000 (16.0Mb) at 0x00000000
      Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank
      Onboard_Flash: Found 1 x16 devices at 0x800000 in 16-bit bank
      Amd/Fujitsu Extended Query Table at 0x0040
      Onboard_Flash: CFI does not contain boot bank location. Assuming top.
      number of CFI chips: 2
      cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
      Creating 8 MTD partitions on "Onboard_Flash":
      0x00000000-0x00020000 : "Boot firmware : 0xA000.0000-0xA001.FFFF"
      0x00040000-0x00200000 : "Kernel - 0xA004.0000-0xA01F.FFFF"
      0x00200000-0x002a0000 : "Config FS - 0xA020.0000-0xA029.FFFF"
      0x002a0000-0x004e0000 : "Root FS- 0xA02A.0000-0xA04D.FFFF"
      0x004e0000-0x00ae0000 : "APP_Modules 0xA04E.0000-0xA0AD.FFFF"
      0x00ae0000-0x00c00000 : "EmergencyRoot 0xA0AE.0000-0xA0BF.FFFF"
      0x00c00000-0x01000000 : "OtherData 0xA0C0.0000-0xA0FF.FFFF"
      0x00020000-0x00040000 : "BootConfiguration 0xA002.0000-0xA003.FFFF"
      ST40_start_host_control
      ST40_start_host_control proceeding
      drivers/usb/host/ehci-stcore.c: ehci_hcd (ST40) at 0xb91ffe00,irq 169

      ST40-ehci ST40-ehci2: new USB bus registered, assigned bus number 1
      ST40-ehci ST40-ehci2: park 0
      ST40-ehci ST40-ehci2: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
      hub 1-0:1.0: USB hub found
      hub 1-0:1.0: 1 port detected
      out
      Initializing USB Mass Storage driver...
      usbcore: registered new driver usb-storage
      USB Mass Storage support registered.
      i2c /dev entries driver
      stssc layer initialized
      STMicroelectronics - Coprocessors st231 Init
      st231-0 Coprocessor -------------------------------------------
      flags 0001 RAM start at 0xa4000000 size 0x00200000
      cop. addr 0x04000000
      Channels : Not defined
      IRQ : not used
      ---------------------------------------------------------------
      st231-1 Coprocessor -------------------------------------------
      flags 0001 RAM start at 0xa4200000 size 0x00200000
      cop. addr 0x04200000
      Channels : Not defined
      IRQ : not used
      ---------------------------------------------------------------
      NET: Registered protocol family 2
      IP: routing cache hash table of 512 buckets, 4Kbytes
      TCP established hash table entries: 2048 (order: 2, 16384 bytes)
      TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
      TCP: Hash tables configured (established 2048 bind 2048)
      NET: Registered protocol family 1
      NET: Registered protocol family 10
      IPv6 over IPv4 tunneling driver
      NET: Registered protocol family 17
      usb 1-1: new high speed USB device using ST40-ehci and address 2
      hub 1-1:1.0: USB hub found
      hub 1-1:1.0: 4 ports detected
      usb 1-1.4: new high speed USB device using ST40-ehci and address 3
      attempt to access beyond end of device
      mtdblock3: rw=0, want=4612, limit=4608
      UDF-fs: No VRS found
      Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
      Moin,

      ist glaube ich kein Original-Image:

      Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
      JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.

      tun: Universal TUN/TAP device driver, 1.6
      tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>


      Update mit einem Notfallimage schon mal probiert?
      Wenn das nicht geht ist wohl eine Notfallwiederherstellung fällig.

      Schau mal hier:
      Kleines UFS 910 HowTo bei Problemen

      Gruß
      Odin
      UFS 910, FW 2.02, WD Elements 500 GB
      UFS 912, FW 2.02 B3, Unicam 3.18, WD Elements 500 GB
      PS3 Fat @ 320 GB, WD TV Live, WD My Book Live 2TB NAS

      Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von „Odin“ ()